Search:

Type: Posts; User: superoman

Page 1 of 3 1 2 3

Search: Search took 0.55 seconds.

  1. Replies
    16
    Views
    7,117

    Re: Flatpack Furniture Fixings

    Contact hafele. The are in Auckland. View their online catalogue. You can pay by credit card over the phone
  2. Re: How do i work out how many tiles i need for the floor?

    Hi

    Its a total of 6.4m2 which is 72 tiles with no wastage.

    It may pay to draw the tiles on your floor plans to figure out the exact number.

    I.e the T shaped bathroom's central bit is .82m...
  3. Replies
    32
    Views
    8,616

    Re: Smoke alarms failing?

    Thanks for all the answers.

    Interestingly enough put another new battery in the Elto Alarm and it seems to go fine!

    My guess is my house has ghosts
  4. Replies
    32
    Views
    8,616

    Smoke alarms failing?

    Has anybody had any failing smoke alarms or batteries?

    Culprit one:Ringgrip expires 2014. Started beeping sporadically, replaced batteries with everready gold, few weeks later beeping again
    ...
  5. Replies
    2
    Views
    792

    Re: Problems with Seagate Free Agent

    Hi

    Ive had two of these drives with this problem. The circuitboard in both of them died. Take the drive out of the freeagent case and either get another external drive case. The computer will...
  6. Replies
    1
    Views
    1,143

    IBM Netvista 8305 16A RAM?

    Hi

    Will be at parents place in a week or so. They have the above computer. Plan to put more ram in it
    Can someone confirm it is DDR RAM - have seen SDRAM written on a few websites as well.
    Is...
  7. Replies
    10
    Views
    7,403

    Re: Repiling / raising a house

    Hi

    I work as a designer in the building industry.

    First thing would be to engage a designer or architect. They will inspect your house and advise. They will also check the district plan to see...
  8. Replies
    92
    Views
    11,039

    Re: What Do you do for a living?

    Im a building designer. (not allowed to call myself an architect because I did not study architecture)
    Currently looking to change direction and find myself a job as a product designer
  9. Replies
    29
    Views
    5,471

    Re: Question about 2 part epoxy

    give topmark products auckland a call. They wil tell you everything you need to know
  10. Replies
    3
    Views
    1,129

    Re: Garden / landscaping advice

    Hi Billy T

    We sell the bags (holds small pebble) rather than sand.
    We have run out of stock, but should be back in stock in two weeks

    PM me

    Thanks

    Peter
  11. Replies
    5
    Views
    5,743

    Re: Nokia C5-03 wireless issues

    i have the c5 03 first phone replaced because wireless did not work properly. Does the search for wlan on the main screen work. You then connect to the web from that menu not the menu with messaging...
  12. Re: Questions about carbide PCB drills - where to get them?

    Try an engineering supply shop like tradezone.
  13. Replies
    10
    Views
    5,716

    Re: Building a CNC Router

    Plastics I have cut are acrylic/polycarbonate. And yes a sharp cutter is always helpful.

    I am guessing you have been cutting pvc or styrene. Yes they are not easy to machine

    If you are wanting...
  14. Replies
    10
    Views
    5,716

    Re: Building a CNC Router

    Hi

    I don't know enough about steppers to give you an diffinative answer, but my gut would be that the ones from typewriters would be too small

    My guess would be that an 18volt drill will be too...
  15. Replies
    13
    Views
    6,556

    Re: Telstra Clear - Paradise

    They are changing the addresses over in groups.

    Parents were changed over, promised that the emails would be re directed (as specified in an email) but later were told this was not possible
    ...
  16. Thread: CNC machines

    by superoman
    Replies
    7
    Views
    3,434

    Re: CNC machines

    Sorry, don't have any photos with me at the moment... not at home

    However the machine is a Multicam from Australia (not to be confused with the US ones)

    multicam.com.au

    my machine is similar...
  17. Thread: CNC machines

    by superoman
    Replies
    7
    Views
    3,434

    Re: CNC machines

    Hi

    I don't have a mini CNC but have a full size one (1200x1200) It was manufactured by a professional manufacturer.

    All I would say would be to make sure it is strong with no flex

    Most of...
  18. Replies
    32
    Views
    9,248

    Re: Dremel? or equivalent

    I presume that the design is about the same size as onscreen.

    I have been involved in design and manufacture for a while.

    If you want to cut it out of 7mm plastic it will be very difficult to...
  19. Replies
    8
    Views
    4,731

    Re: Acrylic Laptop Knee Stand

    Search of companies register:

    Maiden NZ Ltd
    58 Grassmere Rd
    Henderson Valley
    Ph 09 8350328
  20. Replies
    2
    Views
    2,207

    Turning a monitor into a light?

    This idea may sound ridiculous but is it possible?

    Is it possible to turn a monitor into a light. By this I mean. Plug monitor into wall, have it NOT connected to computer, turn the on button on...
  21. Replies
    7
    Views
    2,422

    Re: HDD enclosure - eSATA

    Hi

    Message Me

    I have a used eSAta enclosure that you could buy off me.
    It was a Segate Freeagent drive
  22. Replies
    8
    Views
    3,970

    Re: ISA slot computer needed

    Hi

    Thanks everyone for your help

    I managed to find a running computer with an ISA Slot that was only $20.

    If it breaks I may by a new industrial motherboard or chop of all the wires off the...
  23. Replies
    8
    Views
    3,970

    ISA slot computer needed

    Hi

    The computer that I will be using to run a CNC router (cabinet making machine) has died.

    If anybody has a computer with an ISA slot in it and is in the Wellington region message me....
  24. Replies
    4
    Views
    3,732

    Re: Parallel port install problems

    Thanks for your reply. I am going to be writing software to control an external interface I have for the parallel port. I may have to use windows 95 or improve my programming skills
  25. Replies
    4
    Views
    3,732

    Parallel port install problems

    Hi

    I have installed a second parallel port on my computer. It works, but the address that it uses is not correct, Will this cause any issues?

    The card is a intek21. It shows up as LPT3 when I...
Results 1 to 25 of 67
Page 1 of 3 1 2 3